本文发表在 rolia.net 枫下论坛1. What type of connector is on a 10BaseT network card?
[ ] a) T-connector
[ ] b) RJ-45
[ ] c) RJ-11
[ ] d) Dix connector
[ ] e) Any of the above
2. How many devices can an IDE controller support?
[ ] a) 2
[ ] b) 3
[ ] c) 4
[ ] d) 7
3. How wide is the standard I/O bus on a PCI motherboard?
[ ] a) 3 inches
[ ] b) 16 bytes
[ ] c) 16 bits
[ ] d) 32 bytes
[ ] e) 32 bits
4. How many DIMMs are required to complete a memory bank on a standard
Pentium motherboard?
[ ] a) One
[ ] b) Two
[ ] c) Four
[ ] d) Eight
[ ] e) Any of the above depending on the power configuration, AT or ATX
5. As a rule of thumb, where does pin one on an IDE ribbon cable face
when plugged onto the hard disk drive?
[ ] a) The right side
[ ] b) The left side
[ ] c) The side nearest the power connector
[ ] d) The side closest to the master/slave jumpers
6. After adding a second IDE hard drive to a new Pentium III desktop
computer, the system will not boot the operating system. There are no
POST error messages. What is the most likely cause?
[ ] a) The cables are not connected properly
[ ] b) The drives are not setup as master & slave
[ ] c) The ribbon cable is not terminated
[ ] d) There is a short-circuit somewhere in the system
7. Which end of a SCSI bus must be terminated?
[ ] a) All open connectors
[ ] b) Only the free ends of the cable
[ ] c) Both physical ends
[ ] d) New SCSI adapters don't need termination
[ ] e) The last device in the chain
8. To install a SCSI hard drive at ID 5, which ID jumper(s) must be shorted?
[ ] a) Jumpers 1 and 4
[ ] b) Jumpers 2 and 3
[ ] c) Jumpers 0 and 2
[ ] d) Jumpers 0, 1, and 2
9. What is the default port address and interrupt for COM2?
[ ] a) 03F8, IRQ 4
[ ] b) 02F8, IRQ 4
[ ] c) 0378, IRQ 7
[ ] d) 03F8, IRQ 3
[ ] e) 02F8, IRQ 3
10. When installing a modem that is set explicitly to COM2, what
resource should be disabled in the system setup (CMOS)?
[ ] a) Software (Xon/Xoff)
[ ] b) Interpreted response
[ ] c) COM2
[ ] d) IRQ 4
[ ] e) All of the above
11. After upgrading your computer's CPU from a 333 MHz Celeron to a new
Pentium II 450 MHz processor, the system becomes unstable.
Choose the 2 most likely causes from the following:
[ ] a) Jumper settings weren't switched from Celeron to Pentium II
[ ] b) Celeron motherboards do not support Pentium II CPUs.
[ ] c) Motherboard does not have a 100Mhz front side bus.
[ ] d) The on-board chipset is not compatible with Pentium II CPUs.
[ ] e) The cooling fan is not functioning properly.
[ ] f) The system is using 66Mhz RAM in a 100Mhz system.
12. What is the theoretical maximum throughput of a 10BaseT Ethernet
network?
[ ] a) 10 MHz
[ ] b) 10 Mbps
[ ] c) 100 MHz
[ ] d) 100 Mbps
[ ] e) Depends on the protocol used over the LAN
13. Which of the following network protocols are directly supported by
Microsoft? (Choose all that apply).
[ ] a) TCP/IP
[ ] b) NetBEUI
[ ] c) IPX ODI
[ ] d) Token Ring
[ ] e) IPX/SPX Compatible Protocol
14. Does a router require an IP address to forward packets to a
different subnet under TCP/IP?
[ ] a) No, a router builds a routing table of all subnets so that it
does not need to forward packets.
[ ] b) Yes, but only if the other subnet is in another domain.
[ ] c) Yes, a router forwards IP packets to different subnets.
15. What is the most likely problem if an administrator is unable to
add a new user account or change a user's password in a single domain
environment? (Assume the administrator has full administrative rights.)
[ ] a) The Administrator account has been locked out.
[ ] b) The user name already exists, or the user is already logged in
to the account.
[ ] c) The primary domain controller (PDC) is down or offline.
[ ] d) The administrator must be logged in at the PDC or BDC.
16. If you are establishing a trust relationship between Domain A and
Domain B, which utility would you use to create the trust?
[ ] a) Server Manager
[ ] b) Control Panel -- Server
[ ] c) User Manager for Domains
[ ] d) System Policy Editor
[ ] e) Control Panel -- Services
17. When establishing a one-way trust relationship between
Domain A (Accounts Domain) and Domain B (Resource Domain), which
domain is the trusting domain?
[ ] a) Domain A or B, depending which is created first
[ ] b) Domain B is the trusting Domain
[ ] c) Domain A is the trusting Domain
18. What special designations does Active Directory (AD) give to domain
controllers? (Choose 2.)
[ ] a) PDC
[ ] b) Global Catalog (GC) server
[ ] c) Master Catalog server
[ ] d) Operations Master
19. What important functions does a Global Catalog (GC) server perform for
users in Active Directory (AD)? (Choose 2.)
[ ] a) A GC server lets a user search the entire forest to find
directory information.
[ ] b) A GC server maintains a list of the user's resources.
[ ] c) A GC server enables the logon process by providing universal group
membership information to the domain controller.
[ ] d) A GC server helps users find services anywhere in the world.
20. As the administrator for your company, what can you do to decrease the
traffic that results from queries to the Global Catalog (GC) across sites?
(Choose the best answer.)
[ ] a) Limit GC searches to the local site.
[ ] b) Create separate forests so that searches remain local.
[ ] c) Create additional GC servers so that the GC is available locally.
[ ] d) Create a local catalog so that searches don't cross WAN links.
21. What is the native capacity of DLT IV tape?
[ ] a) 20GB
[ ] b) 35GB
[ ] c) 40GB
[ ] d) All of the above
[ ] e) None of the above
22. If you have a 20GB hard drive, a 36GB hard drive, and a 50GB hard
drive all configured in a RAID level 5 hardware array, approximately
how much total disk space should be available?
[ ] a) 40GB
[ ] b) 56GB
[ ] c) 86GB
[ ] d) 106GB
[ ] e) none of the above
23. Regarding the functional differences between AT and ATX power
supplies, which statement is true?
[ ] a) AT supports soft power-on and 3.3V, ATX does not.
[ ] b) ATX supports soft power-on, AT supplies 3.3V.
[ ] c) AT supports soft power-on, ATX supplies 3.3V.
[ ] d) ATX supports soft power-on and 3.3V, AT does not.
24. What is the theoretical maximum bandwidth of a T3?
[ ] a) 1.5Mbps
[ ] b) 15Mbps
[ ] c) 35Mbps
[ ] d) 45Mbps
25. An Outlook 98 user is working offline with offline folders.
The user tries to access the address book to address his/her message and
discovers that the list is empty or not available.
Why might this be?
[ ] a) The user is tyring to connect via an Internet proxy server.
[ ] b) The user has never downloaded the address book from the server.
[ ] c) The user's address book is not configured for offline use.
[ ] d) The user must connect to the server to access the address book.
[ ] e) The user does not have enough rights to access the address book.
26. Which of the following scenarios represent appropriate situations in
which to use the Last Known Good Configuration in Windows 2000 Professional?
(Choose all that apply.)
[ ] a) You accidentally disable a critical device driver.
[ ] b) You install a new video driver and can't restart the system.
[ ] c) You copy a new driver over an old one while the old one is
active and subsequently encounter problems.
[ ] d) You install a new device driver, restart Win2K, and the system
stops responding.
[ ] e) You experience a startup failure caused by hardware failures
or corrupted files.
General
List 3 to 5 procedures you would implement to help your company
prepare for a total data loss.
List 3 to 5 procedures you would implement to help your company
roll out a new software package, such as Microsoft Office 2000.更多精彩文章及讨论，请光临枫下论坛 rolia.net
[ ] a) T-connector
[ ] b) RJ-45
[ ] c) RJ-11
[ ] d) Dix connector
[ ] e) Any of the above
2. How many devices can an IDE controller support?
[ ] a) 2
[ ] b) 3
[ ] c) 4
[ ] d) 7
3. How wide is the standard I/O bus on a PCI motherboard?
[ ] a) 3 inches
[ ] b) 16 bytes
[ ] c) 16 bits
[ ] d) 32 bytes
[ ] e) 32 bits
4. How many DIMMs are required to complete a memory bank on a standard
Pentium motherboard?
[ ] a) One
[ ] b) Two
[ ] c) Four
[ ] d) Eight
[ ] e) Any of the above depending on the power configuration, AT or ATX
5. As a rule of thumb, where does pin one on an IDE ribbon cable face
when plugged onto the hard disk drive?
[ ] a) The right side
[ ] b) The left side
[ ] c) The side nearest the power connector
[ ] d) The side closest to the master/slave jumpers
6. After adding a second IDE hard drive to a new Pentium III desktop
computer, the system will not boot the operating system. There are no
POST error messages. What is the most likely cause?
[ ] a) The cables are not connected properly
[ ] b) The drives are not setup as master & slave
[ ] c) The ribbon cable is not terminated
[ ] d) There is a short-circuit somewhere in the system
7. Which end of a SCSI bus must be terminated?
[ ] a) All open connectors
[ ] b) Only the free ends of the cable
[ ] c) Both physical ends
[ ] d) New SCSI adapters don't need termination
[ ] e) The last device in the chain
8. To install a SCSI hard drive at ID 5, which ID jumper(s) must be shorted?
[ ] a) Jumpers 1 and 4
[ ] b) Jumpers 2 and 3
[ ] c) Jumpers 0 and 2
[ ] d) Jumpers 0, 1, and 2
9. What is the default port address and interrupt for COM2?
[ ] a) 03F8, IRQ 4
[ ] b) 02F8, IRQ 4
[ ] c) 0378, IRQ 7
[ ] d) 03F8, IRQ 3
[ ] e) 02F8, IRQ 3
10. When installing a modem that is set explicitly to COM2, what
resource should be disabled in the system setup (CMOS)?
[ ] a) Software (Xon/Xoff)
[ ] b) Interpreted response
[ ] c) COM2
[ ] d) IRQ 4
[ ] e) All of the above
11. After upgrading your computer's CPU from a 333 MHz Celeron to a new
Pentium II 450 MHz processor, the system becomes unstable.
Choose the 2 most likely causes from the following:
[ ] a) Jumper settings weren't switched from Celeron to Pentium II
[ ] b) Celeron motherboards do not support Pentium II CPUs.
[ ] c) Motherboard does not have a 100Mhz front side bus.
[ ] d) The on-board chipset is not compatible with Pentium II CPUs.
[ ] e) The cooling fan is not functioning properly.
[ ] f) The system is using 66Mhz RAM in a 100Mhz system.
12. What is the theoretical maximum throughput of a 10BaseT Ethernet
network?
[ ] a) 10 MHz
[ ] b) 10 Mbps
[ ] c) 100 MHz
[ ] d) 100 Mbps
[ ] e) Depends on the protocol used over the LAN
13. Which of the following network protocols are directly supported by
Microsoft? (Choose all that apply).
[ ] a) TCP/IP
[ ] b) NetBEUI
[ ] c) IPX ODI
[ ] d) Token Ring
[ ] e) IPX/SPX Compatible Protocol
14. Does a router require an IP address to forward packets to a
different subnet under TCP/IP?
[ ] a) No, a router builds a routing table of all subnets so that it
does not need to forward packets.
[ ] b) Yes, but only if the other subnet is in another domain.
[ ] c) Yes, a router forwards IP packets to different subnets.
15. What is the most likely problem if an administrator is unable to
add a new user account or change a user's password in a single domain
environment? (Assume the administrator has full administrative rights.)
[ ] a) The Administrator account has been locked out.
[ ] b) The user name already exists, or the user is already logged in
to the account.
[ ] c) The primary domain controller (PDC) is down or offline.
[ ] d) The administrator must be logged in at the PDC or BDC.
16. If you are establishing a trust relationship between Domain A and
Domain B, which utility would you use to create the trust?
[ ] a) Server Manager
[ ] b) Control Panel -- Server
[ ] c) User Manager for Domains
[ ] d) System Policy Editor
[ ] e) Control Panel -- Services
17. When establishing a one-way trust relationship between
Domain A (Accounts Domain) and Domain B (Resource Domain), which
domain is the trusting domain?
[ ] a) Domain A or B, depending which is created first
[ ] b) Domain B is the trusting Domain
[ ] c) Domain A is the trusting Domain
18. What special designations does Active Directory (AD) give to domain
controllers? (Choose 2.)
[ ] a) PDC
[ ] b) Global Catalog (GC) server
[ ] c) Master Catalog server
[ ] d) Operations Master
19. What important functions does a Global Catalog (GC) server perform for
users in Active Directory (AD)? (Choose 2.)
[ ] a) A GC server lets a user search the entire forest to find
directory information.
[ ] b) A GC server maintains a list of the user's resources.
[ ] c) A GC server enables the logon process by providing universal group
membership information to the domain controller.
[ ] d) A GC server helps users find services anywhere in the world.
20. As the administrator for your company, what can you do to decrease the
traffic that results from queries to the Global Catalog (GC) across sites?
(Choose the best answer.)
[ ] a) Limit GC searches to the local site.
[ ] b) Create separate forests so that searches remain local.
[ ] c) Create additional GC servers so that the GC is available locally.
[ ] d) Create a local catalog so that searches don't cross WAN links.
21. What is the native capacity of DLT IV tape?
[ ] a) 20GB
[ ] b) 35GB
[ ] c) 40GB
[ ] d) All of the above
[ ] e) None of the above
22. If you have a 20GB hard drive, a 36GB hard drive, and a 50GB hard
drive all configured in a RAID level 5 hardware array, approximately
how much total disk space should be available?
[ ] a) 40GB
[ ] b) 56GB
[ ] c) 86GB
[ ] d) 106GB
[ ] e) none of the above
23. Regarding the functional differences between AT and ATX power
supplies, which statement is true?
[ ] a) AT supports soft power-on and 3.3V, ATX does not.
[ ] b) ATX supports soft power-on, AT supplies 3.3V.
[ ] c) AT supports soft power-on, ATX supplies 3.3V.
[ ] d) ATX supports soft power-on and 3.3V, AT does not.
24. What is the theoretical maximum bandwidth of a T3?
[ ] a) 1.5Mbps
[ ] b) 15Mbps
[ ] c) 35Mbps
[ ] d) 45Mbps
25. An Outlook 98 user is working offline with offline folders.
The user tries to access the address book to address his/her message and
discovers that the list is empty or not available.
Why might this be?
[ ] a) The user is tyring to connect via an Internet proxy server.
[ ] b) The user has never downloaded the address book from the server.
[ ] c) The user's address book is not configured for offline use.
[ ] d) The user must connect to the server to access the address book.
[ ] e) The user does not have enough rights to access the address book.
26. Which of the following scenarios represent appropriate situations in
which to use the Last Known Good Configuration in Windows 2000 Professional?
(Choose all that apply.)
[ ] a) You accidentally disable a critical device driver.
[ ] b) You install a new video driver and can't restart the system.
[ ] c) You copy a new driver over an old one while the old one is
active and subsequently encounter problems.
[ ] d) You install a new device driver, restart Win2K, and the system
stops responding.
[ ] e) You experience a startup failure caused by hardware failures
or corrupted files.
General
List 3 to 5 procedures you would implement to help your company
prepare for a total data loss.
List 3 to 5 procedures you would implement to help your company
roll out a new software package, such as Microsoft Office 2000.更多精彩文章及讨论，请光临枫下论坛 rolia.net